Light To Medium Weight Fabric Automatic Spreading Machine
Spreading machine allowing spreading of all types of textile fabrics. Automatic machine equipped with cradle-feed system with belts, direct-drive driving system, operator platform and intuitive, easy to use color touchscreen. All four wheels of the spreading machine are driven. The machine is equipped with an automatic fabric edge alignment system. Tensionless spreading of fabrics assures perfect quality over the whole height of spread marker. Automatic cutting of each spread layer. In standard configuration the machine is delivered with auotomatic end cutter and movable catcher to keep the end of fabric layers. Optionally available with a zigzag equipment, fixed catcher, Tray for flat-folded unit (spreading of fabric stored folded on a pallet), tubular unit and etc.
MAIN ADVANTAGES OF MASTER [MT1] USAGE
Elimination of manual spreading and layering of fabrics which is the weakest part of the cutting room production chain
Several times increase of spreading efficiency for each type of fabric
Only one operator results in significant reduction of work costs
Very fast spreading of mattresses for small series and single production orders
Constant quality of spreading independent of length of spread marker with elimination of fabric tensioning in different
layers what’s a typical problem for manual spreading
Easy and intuitive operation, possible also for not-qualified personal
Perfect reliability of operator assures continuous production and lowest possible costs of maintenance
Fast and solid service assured by experienced technicians
OPERATIONAL SPECIFICATIONS OF MASTER [MT1]
√ CRF – Cradle feed with a system of feeding belts assuring easy loading and unloading of fabric rolls
√ AEC – Automatic alignment of fabric edge of all spread fabric layers
√ STD – Spreading of fabrics in standard system (right side up with transversal cutting)
√ ZZG – Set of front and end catchers allowing zig-zag spreading (left side to right side)
√ IFS – Intelligent fabric feeding system with dynamic measurement of fabric tension during spreading
gives the possibility to control fabric tension
√ NTF – Non-Tension Feeding – tensionless feeding and spreading of fabric
√ Easy inversion of spreading side (right side up or left side up)
√ Automatic re-winding (feeding and rolling back) with fabric edge alignment
√ Automatic stop of the machine when fabric is finished with audible signal
√ Programmable shifting points allows for fast cutting of the places with faults and continuation of work
√ Software calculates length of spread fabric with reporting of fabric usage
√ ARC – Automatic one-side cutting of fabric by a transversal cutting unit with rotary blade
√ ACL – Automatic adjustment of cutting unit slat to height of currently spread height of layers
√ ODP – Movable operator platform [which can be closed and locked] facilitates usage and assures
highest possible spreading speed
√ TFT – Color touchscreen (LG) assures easy and comfortable adjustments of working parameters
√ 10PR – Possibility to store in memory of the touchscreen up to 10 parameter profiles for different fabrics
√ ASS – Automatic stoppage of machine’s movement after approaching to an obstacle assures safety of
operator and other personnel which could stand close to the machine
√ Seamless cradle feed belt instead of slit belts assures that no fabric edge will go under it
√ Available with different types of spreading tables – most commonly used are 30mm
Heavy tables with or without air flotation system & Conveyorized tables
√ Wide range of wheels position adjustments allows adaptation of new machine to an already installed
spreading table, what’s significantly reducing investment’s costs
√ System of semi-automatic fabric winding from fabric roll
√ Programmable acceleration and deceleration in extreme positions of the table
√ Encoder always gives information about current position of the machine on the table
√ Current metered spread fabric length is shown on the panel
√ Multi-function throttle controls movement of the machine along the table or adjusts the amount of fabric feeding
√ Automatic self-test of the machine on each turning on of the machine or upon request of the operator makes
it easy to check the state of the machine
√ “Quick-Stop” emergency switches on both sides of the machine assure accordance with current CE requirements
MAIN SPECIFICATIONS
Machine Model: Master [MT1]
Machine Name: Light to medium weight Automatic Fabric Spreading Machine
Material Use: Fabrics such as Woven, knit, jeans, Full Lycra, etc.
Ease Of Use: Material roll cradle feed system tilts automatically for easy material loading and unloading.
Fabric Width: 000 cm
Roll Diameter: 650 mm max
Machine Speed: 0-100 mt/min with speed control (depends on fabric style)
Spreading Height: 250 mm Maximum with cutting Unit / 200 mm Maximum with zig zag spreading height /
200 mm Maximum with tubular unit
Fabric Weight: 200 kg max.
Loading Fabric: Easy load with electrical cradle tilt
Main Spreading Motor: 1.10 kW 1500 Rpm AC Motor with Gearbox (PGR Drive Technologies)
Cradle Left-Right: 0.25 kW 1500 Rpm AC Motor with Gearbox (WAT)
Cradle Feed: 0.75 kW 1500 Rpm AC Motor with Gearbox (PGR Drive Technologies)
Lift Motor: 0.30 kW 24V DC with Gearbox (KORMAS)
Fabric Edge Cutter: Clack Motor (24V DC),Knife transfer motor (24V DC) with gearbox, Knife Rotate (24V DC) (Kormas)
Control Modes: Automatic or Manuel control
Edge Control: Edge control with 2 Photocells
No Cloth Stop Funct: Automatic stop with 1 photocell control when fabric is over
Safety Device: 2 security photocells to stop the machine if someone step in front/rear side of the machine.
Height Photocell: A photocell which moves lift while spreading height goes up
Electronic System: Special software with LG PLC
Control System: LG 5,7 inch Touch Screen
Drivers: 2 LG Invertors
Settings From Control Panel:
√ Level count √ Spreading Length √ Spreading Speed (forward and backward) √ Tension Settings
√ Using with Password √ Zigzag or One way Selection √ Tension Setting at Start or Stop
√ Disabling Security Sensor if Needed √ Disabling Fabric Over Sensor if Needed
Machine Dimensions:
Machine Weight:
Installed Power: 5 kW 220 volt
Attachments: Automatic cutting device & Movable catcher [standard]
Paint: Main with electrostatic paint, covers with wet paint
Operator Platform: Allows operator to ride alongside the table
Spreading Table:
Table Length: 12,6 Meter
Table Width: 220 cm. Special construction that can be used with MT1 Master
Table Electric System: EAE Busbar System
Paint: Electrostatic Paint
Table Height: Between 840-870 mm
Rail System: Enable for MT1 Master and its platform